Featuring Fail Safe, USB & Quick Boot Modes
SVGA       LVDS Flat Panel     2 USB  Ethernet 100Base-Tx 10Base-T			Audio   COM2 COM1     multiPort: Parallel Floppy(*) aDIO™ Utility: Keyboard Speaker Battery Reset
	Power	EIDE                PS/2 Mouse
	CMX147786CX400HR-256 cpuModule™ (*)  Interfaces only with RTD modified floppy drive Solder-tail expansion bus, right-angle I/O & feed-thru I/O connectors available on request
ISA (PC/104)			PCI (PC/104+)
	Standard Rugged Passive Heatsinks
	Rugged Fanless IDAN™ & HiDAN™ Configuration -40°C to +85°C

• 400 MHz, 0.95Vdc Intel Celeron^™ with thermal throttling
• 128, 256 & 512 Mbytes SDRAM
• 32 pin SSD socket
  • Miniature 1GB ATA/IDE Flash Disk installed unless otherwise specified; 4GB optional
  • Natively supported by all major operating systems
• 4 Bus Master Add-on Cards Supported 
• Rugged Passive Heatsink
• Passive Structural Heatsink & Heatpipes in IDAN^™ and HiDAN^™ System Configurations
• Advanced Programmable Interrupt Controller (APIC)
• RTD Enhanced Award BIOS with ACPI, Quick Boot and USB Boot
• Nonvolatile Configuration
• multiPort with Parallel Port, Floppy Drive Interface and 18-bit Digital I/O Port with Advanced Digital Interrupt Modes
• INTEL 82559 Fast Ethernet
  • 10BASE-T and 100BASE-Tx
  • Full Duplex support
• AC97 Audio Support
• AGP S3 Savage SVGA controller with LVDS Flat Panel output
• 64-bit AGP Hardware graphics-accelerator 2-32 Mbytes selectable shared video memory
• DirectX & OpenGL 3D Accelerator
• 3.3V or 5V PCI bus signaling
• Two RS-232/422/485 Ports
• Two USB (Universal Serial Bus) Ports
• EIDE Controller with UltraDMA 33/66/100
• PS/2 Mouse Port
• Keyboard Port
• Speaker Port
• Mating Connectors
  • Standard 4-pin 0.1" DIL header (PS/2 Mouse)
  • Standard 12-pin 0.1" DIL header (Power)
  • Standard 10-pin 2mm DIL header (Utility, COM1, COM2, Audio, SVGA, USB, Ethernet)
  • Standard 20-pin 2mm DIL header (Panel)
  • Standard 26-pin 2mm DIL header (multiPort)
  • Standard 44-pin 2mm DIL header (EIDE)

Features:

• Complete PC-compatible motherboard
• Stackable 104-pin PC/104 AT bus
• Stackable 120-pin PC/104-Plus PCI bus
  • 4 Bus Master Add-on Cards Supported
• Supports MMX instructions
• Math coprocessor
• 32KB L1 and 256KB L2 internal cache
• Boot Block Flash BIOS with Quick Boot Option
• Boot from USB Device
• Nonvolatile configuration without battery
• Y2K compliant real time clock (external battery required)
• Watchdog timer
• 7 DMA channels
• 24 interrupt channels with APIC enabled (15 in legacy PIC mode)
• 3 timer/counter channels
• High resolution 100 MHz APIC timer
• Advanced Configuration and Power Interface (ACPI)
• ACPI 1.0 Compliant
• Supported power down modes: S1 (Power On Suspend), S4 (Hibernate), and S5 (Soft-Off)
• CPU Clock Throttling and Clock Stop for C0 to C3 Support
• Also supports APM 1.2 for legacy power management
• Advanced Thermal Management
  • Thermal Throttling reduces clock speed to prevent thermal runaway
  • Auto Fan Control only runs fan when needed
  • SMBus Temperature Monitor for CPU and board temperature
• 32 pin SSD socket
  • Miniature 1GB ATA/IDE Flash Disk installed unless otherwise specified; 4GB optional
  • Natively supported by all major operating systems

I/O:

• AC97 Audio Support
  • SoundBlaster Compatible
  • Selectable Headphone or Line level output
  • Line level input
  • Microphone input

• INTEL 82559 Ethernet

  • Ethernet Controller
    • Intel 82559ER Fast Ethernet PCI Controller
    • Integrated 3KByte Transmit and 3Kbyte Receive FIFOs
  • Physical Layer
    • 100Base-Tx and 10Base-T
    • Full Duplex support
  • Easy to Use
    • Low Power Features
    • Status LEDs
    • Software configuration
• Pro Savage4 AGP Graphics controller Super VGA CRT and LVDS Flat Panel interface
  • Resolution up to 1920 x 1440 pixels with 32K colors
  • VGA, SVGA, XGA, SXGA, UXGA
  • Up to 16 million colors
  • High-performance memory
    • 2MB to 32MB of shared SDRAM memory
• Software-configurable RS-232/422/485 serial port
  • 16550 compatible UARTs for high-speed
  • Termination resistors for RS-422/485
• multiPort function connector
  • Parallel port
    • SPP, PS/2 bi-directional, EPP & ECP
  • Advanced Digital I/O (aDIO^™)
    • One 8-bit port programmable as input or output
    • Eight bit-programmable I/O with Advanced Digital Interrupt Modes
      • Event Mode Interrupt generates an interrupt when any input bit changes
      • Match Mode Interrupt generates an interrupt when input bits match a preset value
      • External Strobe Mode latches 8 data inputs and generates and interrupt
    • Two Strobes can be configured as readable inputs.
  • Floppy controller interface - Interfaces only with RTD's XK-CM49 multiPort Floppy Drive and Cable Kit
• Two USB 1.1 Universal Serial Bus) Ports
  • Supports both 12Mb/s (full-speed) and 1.5Mbs (lowspeed) peripherals
  • 500 mA @ 5 Vdc provided per port

• UltraDMA-100 / 66 / 33 Master Mode PCI EIDE Controller

  • Transfer rate up to 100MB/sec using UltraDMA
  • Increased reliability using UltraDMA-33 transfer protocols
  • Increased performance using UltraDMA-100 mode 5
  • Support ATAPI compliant devices including DVD drives
  • 48-bit LBA support for hard drives larger than 137GB
• PS/2 Mouse port
• Utility port
  • XK-CM61 Cable Kit Included
  • PC-AT compatible keyboard port
  • Speaker (0.1W output) port
  • Hardware Reset input
  • Battery input for Real Time Clock
• Power I/O
  • Access to PC/104 Bus power pins
    • Gnd, ±12 & 5 VDC
  • Access to PC/104-Plus Bus pins
    • Gnd, ±12, 5 & 3.3 VDC

• RTD Enhanced Award BIOS with built-in SETUP, USB Boot and Quick Boot Mode Installed
• Fail Safe Boot Mode using embedded ROM-DOS
• Includes ROM-DOS , SSD software, utilities, and example programs.
• Compatible with all x86 operating systems:
• MS-DOS, ROM-DOS, PC-DOS
• Windows (98, NT 4.0, 2000, XP, and XP Embedded)
• Linux (desktop and real-time versions)
• RTOSes such as QNX, VxWorks, and Windows CE

• Dimensions
  • Board Size: 90.17 mm L x 95.89 mm W (3.550 in L x 3.775 in W)
  • I/O Ext: 12.70 mm E_L x 79.38 mm E_W (0.350 in E_L x 3.125 in E_W)
• Weight: Approximately 0.14 Kg (0.30 lbs.)
• Standard Operating Temperature: -40° to +85°C: 90% humidity non-condensing
• Storage Temperature: -40° to +85°C
• MTBF: 110,000 hours typical
• Power requirements   400 MHz:  7.6 W @ 5 VDC Typical

Recommended Accessories:

• Cable Kit XK-CM43
• Cable Kit XK-CM49 (multiPort Floppy Drive)
• CMT3106 or CMT36106

Documentation and Software Downloads:

• Hardware Manual
• Drivers and Example Programs
• Software Manual(s)
• Application Notes

Ordering Information

* 1GB ATA/IDE Flash Disk installed unless otherwise specified; 4GB optional.

Third Party Information     IDAN™ Systems

CPU Guide     PC104 Menu     Accessories     Development Kits     Home

Copyright © 1998-2006 RTD Embedded Technologies, Inc.  All rights reserved.